Short answer: if you only need to extract stale, damp air from wet rooms, a DucoBox MEV unit (Reno, Silent or Focus) is the right family. If you want to supply fresh air as well and recover heat from the air you throw away, you need a DucoBox MVHR unit (Energy Sky, Energy Comfort, Energy Comfort Plus or Energy Premium). This guide walks through the whole DUCO range stocked at PureClima so you can narrow it to one or two models before you buy.

MEV or MVHR: the first decision
MEV stands for mechanical extract ventilation. A single fan unit pulls air continuously from kitchens, bathrooms, WCs and utility rooms through ducting, and fresh air replaces it through trickle vents or other background openings. It is simple, compact and the lowest-cost route to continuous ventilation.
MVHR stands for mechanical ventilation with heat recovery. The unit extracts from wet rooms and supplies filtered fresh air to bedrooms and living rooms at the same time, passing both airstreams through a heat exchanger so warmth from the outgoing air pre-warms the incoming air. It needs two duct runs instead of one and a reasonably airtight building to make sense, but it reduces heat loss through ventilation and lets you filter incoming air.
In Part F of the Building Regulations these correspond broadly to continuous mechanical extract (System 3) and continuous mechanical supply and extract with heat recovery (System 4). Your designer or Building Control body will confirm which applies to your project.
The DucoBox MEV range
DucoBox Reno — renovation and refurbishment
The DucoBox Reno MEV unit is the compact option, rated at 325 m³/h (90 l/s) at 150 Pa. It measures 381 × 366 × 204 mm, weighs 3.1 kg and offers four Ø125 mm extract connections plus one at the rear, with a single Ø125 mm outlet. It runs on 230 VAC with a peak draw of 47 W and communicates by RF.
That small footprint is the point: it is intended for flats, terraced houses and refurbishment work where there is very little room for plant. If you want the unit, a controller and valves in one order, the DucoBox Reno All-in-One Kit bundles the MEV unit, a controller and three DucoVent Basic valves.
DucoBox Silent — quiet central extract
The DucoBox Silent MEV unit steps up to 400 m³/h (111 l/s) at 150 Pa with seven Ø125 mm extract connections and one Ø125 mm outlet, so it can serve more wet rooms from a single box. It measures 480 × 480 × 194 mm, weighs 4.3 kg and peaks at 84 W on a 230 VAC supply, again with RF communication. The shallow depth suits cupboard and loft installations. A Silent Connect All-in-One Kit version is also stocked.
DucoBox Focus — demand-controlled zonal extract
The DucoBox Focus is the intelligent end of the extract range. Its patented CO₂ and humidity control valves regulate airflow automatically, so air is extracted where and when it is actually needed rather than at a fixed rate everywhere. A built-in NightBoost function increases night-time ventilation to help limit overheating.
Because the intelligence sits in the valves, a Focus system is usually specified as a package. The Focus System Basic Kit includes control valves, a user controller and a Silent Plus kit, and the Focus System Basic Kit with Bedroom Extraction adds a fifth control valve for bedroom extract.
For a closer look at how these three units differ in use, read DucoBox Silent & Focus MEV explained.
The DucoBox MVHR range

DucoBox Energy Sky D275 — hidden in a ceiling void
The Energy Sky D275 is the flat, ceiling-mounted unit: 275 m³/h (76 l/s) at 200 Pa, four Ø160 mm duct connections, 670 × 1180 × 295 mm, 19 kg, with a maximum 65 W per motor. The shallow 295 mm depth is what makes it work in apartments and compact homes where no cupboard can be given over to plant.
DucoBox Energy Comfort D325 and D400
The Energy Comfort D325 delivers 325 m³/h (90 l/s) at 150 Pa through four Ø160 mm connections, measures 700 × 705 × 525 mm, weighs 21 kg and uses two 59 W fans. The Energy Comfort D400 moves up to 400 m³/h (111 l/s) at 200 Pa on four Ø180 mm connections, measures 756 × 800 × 584 mm, weighs 31 kg and uses two 72.5 W fans. Both use DUCO's patented double bypass with software-selectable left or right handing.
DucoBox Energy Comfort Plus D350, D450 and D550
The Comfort Plus units add automatic calibration and more capacity: D350 at 350 m³/h (97 l/s at 200 Pa), D450 at 450 m³/h (125 l/s at 200 Pa) and D550 at 550 m³/h (153 l/s at 200 Pa). Our dedicated article, DucoBox Energy Comfort Plus MVHR, covers these three in detail.
DucoBox Energy Premium — the flagship
The Energy Premium is DUCO's top MVHR platform, offered at 325 m³/h (90 l/s) or 400 m³/h (111 l/s) at 150 Pa, in one-zone or two-zone versions, with or without an integrated pre-heater, and in left-hand or right-hand orientation. All versions share a 740 × 957 × 585 mm casing with five Ø160 mm duct spigots (Ø190 mm external) and carry an A+ energy label with 88–89% efficiency measured to EU 1253/2014.
Sixteen variants is a lot to sift through, so we have written a separate decision guide: DucoBox Energy Premium 325 vs 400.
At a glance
| Unit | Type | Capacity | Duct connections | Typically suits |
|---|---|---|---|---|
| DucoBox Reno | MEV | 325 m³/h (90 l/s) at 150 Pa | 4 × Ø125 + 1 rear, outlet Ø125 | Flats, terraces, refurbishment |
| DucoBox Silent | MEV | 400 m³/h (111 l/s) at 150 Pa | 7 × Ø125, outlet Ø125 | New build and renovation, more wet rooms |
| DucoBox Focus | MEV, demand-controlled | See product page | See product page | Homes wanting room-by-room control |
| Energy Sky D275 | MVHR | 275 m³/h (76 l/s) at 200 Pa | 4 × Ø160 | Ceiling voids, apartments |
| Energy Comfort D325 | MVHR | 325 m³/h (90 l/s) at 150 Pa | 4 × Ø160 | Houses and apartments |
| Energy Comfort D400 | MVHR | 400 m³/h (111 l/s) at 200 Pa | 4 × Ø180 | Larger homes |
| Energy Comfort Plus D350/D450/D550 | MVHR | 350 / 450 / 550 m³/h at 200 Pa | See product pages | Larger homes needing auto calibration |
| Energy Premium 325 / 400 | MVHR | 325 or 400 m³/h at 150 Pa | 5 × Ø160 (ext. Ø190) | Passive and low-energy homes |
A short selection checklist
- Design airflow. Work from the ventilation rate your designer has calculated, then choose a unit whose rated flow at the relevant pressure comfortably exceeds it.
- Space and access. Measure the plant space in all three dimensions, and check you can still reach the filters after installation.
- Duct diameter. Ø125, Ø160 and Ø180 all appear across the range. The unit's connections must match your duct design.
- Handing. Energy Premium is ordered as left-hand or right-hand; Energy Comfort handles this in software.
- Zoning. If you want day and night zones controlled separately, choose a two-zone Energy Premium.
- Frost protection. Energy Premium is available with an integrated pre-heater; a separate pre-heater accessory is listed for Energy Comfort (Plus).
- Controls. Decide early whether you want CO₂ or humidity sensing, because this affects which sensors and valves you order with the unit.
What to confirm before you order
Check the exact model number and variant on the product page, the physical dimensions against your plant space, the duct diameters against your design, and — for Energy Premium — zone count, heater and handing. If you are replacing an existing unit, confirm the new unit's spigot positions suit the ductwork you intend to keep. Where you are unsure, our team can check a specification with you before anything is ordered.
Frequently asked questions
Can I upgrade an MEV unit to demand control later?
DUCO lists box sensors for several units, including humidity and CO₂ box sensors for DucoBox Silent and Focus and a humidity box sensor for Energy Premium. Compatibility is model-specific, so check the sensor's product page against your unit before ordering. Our guide to Duco sensors and controls explains the options.
Do I still need air valves?
Yes. Every extract and supply point needs a terminal. The DucoVent range covers everything from the plain Basic valve to plastered-in Trimless and acoustic Design valves.
What about the ductwork?
DUCO's semi-rigid system, plenums, silencers and terminals are covered in DucoFlex ventilation ducting explained.
How often do the filters need changing?
DUCO filter sets are listed with a typical replacement interval of every 6 to 12 months, depending on the unit and local air quality. Our Duco MVHR filter guide matches each filter set to its unit.
Next step
If you already know whether you need extract-only or heat recovery, browse the MEV units or MVHR units collections and compare the shortlisted models side by side. If you would rather have the specification checked first, contact PureClima for advice and we will help you match a DucoBox to your project.

