Short answer: DucoFlex in-line silencers come in two constructions — flexible and semi-rigid — each 1000 mm long, in diameters from Ø125 to Ø200 mm. Fit one between the DucoBox and the manifold to stop fan noise travelling into the duct network, and choose the diameter to match the duct at that point. The construction you pick depends mainly on how the duct is routed.

Where MVHR noise actually comes from
A heat recovery unit makes three different kinds of noise, and they need different remedies.
Fan noise travelling down the ducts is the one silencers address. The fan is a broadband noise source sitting directly at the end of a duct that leads to a bedroom ceiling. Without something to absorb it, that sound arrives at the valve.
Air noise generated in the ducts themselves comes from air moving too fast — undersized duct, a sharp bend, or a valve throttled almost shut. A silencer will not fix this, because the noise is created downstream of it. The cure is correct duct sizing, covered in our guide to DucoFlex duct sizes.
Structure-borne vibration travels through the unit's mountings into the building fabric. That is a job for anti-vibration mounting and careful fixing, not for a duct silencer.
Buying a silencer to cure a whistle caused by undersized duct is a common and expensive mistake. Diagnose first.
The two constructions
Every DucoFlex silencer stocked at PureClima is 1000 mm long. The difference is the body.
Flexible silencers
A flexible silencer can take up a slight misalignment between the unit and the duct, which is useful in a tight plant cupboard where the connection is never quite square. It also helps interrupt vibration travelling along the duct itself.
- Flexible silencer Ø125 mm, 1000 mm
- Flexible silencer Ø125 mm (M/F), 1000 mm
- Flexible silencer Ø160 mm (M/M), 1000 mm
- Flexible silencer Ø180 mm (M/M), 1000 mm
- Flexible silencer Ø200 mm (M/F), 1000 mm
Semi-rigid silencers
A semi-rigid silencer holds its shape, which keeps the internal bore consistent and makes it the tidier choice on a straight, supported run. Where there is room to install it properly, it is the more predictable component.
- Semi-rigid silencer Ø160 mm (M/M), 1000 mm
- Semi-rigid silencer Ø180 mm (M/M), 1000 mm
- Semi-rigid silencer Ø200 mm (M/M), 1000 mm
Matching the range to your unit
| Diameter | Flexible | Semi-rigid | Typical duct context |
|---|---|---|---|
| Ø125 mm | Yes (plain and M/F) | — | MEV units and smaller branches |
| Ø160 mm | Yes (M/M) | Yes (M/M) | Most MVHR unit connections |
| Ø180 mm | Yes (M/M) | Yes (M/M) | Larger MVHR connections |
| Ø200 mm | Yes (M/F) | Yes (M/M) | Main runs on larger systems |
Check the end configuration as well as the diameter. M/M means male on both ends and needs a female fitting or coupler each side; M/F has one of each, which can save a connector. Ordering the wrong combination is an easy mistake because the diameter is the part everyone looks at.
Your unit's connection size determines where to start: Ø125 mm on the MEV units, Ø160 mm on most MVHR models and Ø180 mm on the Energy Comfort D400. The DucoBox range guide lists them all.
Where to fit them
The standard position is between the DucoBox and the manifold, on both the supply and the extract side. Supply is the side occupants notice, because that air is delivered into bedrooms and living rooms, but treating extract as well stops noise being carried into bathrooms and the hallway.
Keep a short straight section either side of the silencer rather than bolting it directly onto a bend. A silencer immediately followed by a sharp turn generates some of the turbulence it was installed to prevent.
Where ducts pass between dwellings or between a plant cupboard and a bedroom, a silencer also reduces crosstalk — conversation travelling from one room to another along a shared duct route.
Before you order, confirm
- The duct diameter at the point the silencer will sit — not the unit's largest connection
- End configuration, M/M or M/F, and what couplers that implies
- 1000 mm of straight space, plus the fittings at each end
- Whether you are treating supply only, or supply and extract
- That the noise you are chasing is fan noise, not undersized ductwork
- Support for the silencer's weight, particularly on a horizontal run
Frequently asked questions
How much quieter will it be?
That depends on the fan, the duct layout, the room and the background noise level, so we will not quote a figure that could not be relied on. The useful statement is directional: a silencer between unit and manifold reduces fan noise carried into the duct network, and it is standard practice on MVHR installations for that reason.
Do I need one on every branch?
Normally no. One on the supply duct and one on the extract duct, close to the unit, treats the whole network. Individual branches are only treated where a particular room needs extra care or where crosstalk between two rooms is the problem.
Flexible or semi-rigid — which is better?
Neither is better in general. Semi-rigid is the cleaner installation on a straight supported run; flexible is more forgiving where the connection is awkward or slightly out of line.
Can a silencer go inside a ceiling void?
Yes, provided it is supported and remains accessible enough for the duct connections to be inspected. Remember it is 1000 mm long, which is more space than people allow for when planning.
Next step
Compare the full range in the duct silencers collection, and see manifolds, adapters and flow regulators for the fittings either side of them. If you are not sure whether your noise problem is a silencer problem, describe it to us and we will tell you honestly.

