Skip to content

Free Ventilation estimate  01283 380031 

✌🏼 Next Day Delivery

Cart
Air Valves

DucoVent Air Valves Compared: Basic, Comfort, Premium and Design AK

Short answer: all the DucoVent valves stocked at PureClima connect to Ø125 mm duct, so the choice is about appearance, adjustment and acoustics rather than fit. Basic is the plain, lowest-cost valve; Comfort adds pre-settable positions; Premium gives a paintable finish with fine 34-position adjustment, in trimmed or plastered-in trimless versions; and Design AK is the acoustic, architectural range.

DucoVent Design Round AK acoustic air valve, Ø125 mm

What an air valve has to do

An air valve is the visible end of a ventilation system — the terminal where air is drawn out of a wet room or delivered into a bedroom. It has three jobs: pass the design flow rate without excessive resistance, let that flow be set and balanced at commissioning, and look acceptable on the ceiling or wall for the next twenty years. Different valves weight those three differently, which is the whole basis for the range.

DucoVent Basic

The DucoVent Basic air valve is a white plastic valve for Ø125 mm duct, rated to a maximum 75 m³/h and suitable for both extraction and supply.

It is the straightforward specification for utility rooms, WCs, plant areas and rented or budget-led projects — anywhere the valve simply needs to work and disappear. It is also the valve supplied in the DucoBox Reno All-in-One Kit.

DucoVent Comfort

The DucoVent Comfort air valve shares the Ø125 mm connection, white finish and 75 m³/h maximum flow, and adds pre-settable positions for extraction or supply.

That matters at commissioning. A pre-settable valve can be adjusted to its design flow and then left alone, so a household cleaning the ceiling cannot change the balance of the system by twisting the valve core. For a general-purpose extract or supply point it is usually worth the small step up from Basic.

DucoVent Premium: Trim and Trimless

DucoVent Premium Trimless air valve, Ø125 mm, white, plastered-in finish

The Premium valves are rated to a maximum 50 m³/h on Ø125 mm duct, in a paintable white finish, and both are available in white and black.

  • Premium Trim — fitted with a visible trim ring, and adjustable across 34 positions for precise balancing.
  • Premium Trimless — plastered in, so the valve face sits flush with the ceiling with no visible rim.

Both are also listed in black and trimless black. Note the lower 50 m³/h maximum: if a room's design flow is above that, a Premium valve is not the right terminal for it regardless of how good it looks.

The trimless version has to be planned in. It is installed as part of the plastering sequence, which means telling the plasterer before the ceiling is finished, not after.

DucoVent Design AK: the acoustic range

The Design AK valves are the architectural option, with acoustic treatment, a 52 mm depth and a stated noise level below 15 dB(A) at 50 m³/h. Maximum flow is 75 m³/h on extract and 50 m³/h on supply, on a Ø125 mm connection.

Model Face size Suitable for
Design Round AK Ø215 mm Extraction + supply
Design Square Standard AK 180 × 180 mm Extraction
Design Square XL AK 215 × 215 mm Extraction + supply
Design Rounded Square Standard AK 180 × 180 mm Extraction
Design Rounded Square XL AK 215 × 215 mm Extraction + supply

Two things to take from that table. First, the Standard face sizes are listed for extraction only, while the XL faces and the round valve are listed for extraction and supply — so a scheme that wants one shape throughout should generally be built around the XL sizes. Second, the shape choice is purely visual: round, square, or square with softened corners, at 180 mm or 215 mm across.

Comparison at a glance

Basic Comfort Premium Trim / Trimless Design AK
Connection Ø125 mm Ø125 mm Ø125 mm Ø125 mm
Max flow 75 m³/h 75 m³/h 50 m³/h 75 extract / 50 supply
Adjustment — Pre-settable positions 34 positions See product page
Finish White plastic White Paintable white or black Architectural, acoustic
Acoustic rating — — — <15 dB(A) at 50 m³/h
Best for Utility, WC, budget General extract and supply Clean ceilings, fine balancing Bedrooms, living rooms, exposed ceilings

Installing into plasterboard

Where a valve lands in a plasterboard ceiling, the Ø125 mm plasterboard sleeve for DucoVent gives the valve a rigid, correctly sized housing to seat into, instead of relying on the board edge. It is an inexpensive part that makes the finished result considerably tidier.

For the ductwork that feeds the valves — plenums, semi-rigid pipe, silencers and terminals — see DucoFlex ventilation ducting explained.

Before you order, confirm

  • The design flow for each room, against the valve's maximum — particularly the 50 m³/h limit on Premium
  • Whether that position is extract or supply, since some Design AK models are listed for extraction only
  • Duct diameter at the terminal: every valve here is Ø125 mm
  • Ceiling build-up and depth, and whether a plasterboard sleeve is needed
  • Colour, where white and black are separate product listings
  • For trimless valves, that the plastering sequence allows for them

Frequently asked questions

Can I use the same valve for extract and supply?

The Basic and Comfort valves are listed as suitable for extraction and supply. Among the Design AK valves, the Round and the XL sizes are listed for both, while the Standard square faces are listed for extraction. Always check the product page for the specific model.

Do these valves fit any DucoBox?

They are terminals, so what matters is the duct size and the room's design flow rather than the unit model. Both MEV and MVHR systems use them — see our guide to the DucoBox range if you are still choosing a unit.

What about rooms that need demand control at the valve?

That is a different product. Duco's sensing control valves are part of a DucoBox Focus system and are covered in Duco sensors and controls explained.

Can Premium valves be painted to match the ceiling?

They are listed with a paintable white finish. Follow DUCO's guidance on paint type and avoid building up coats on moving parts, which would affect the adjustment.

Next step

Compare the full range in the air valves and vents collection. If you already know each room's design flow and whether it is extract or supply, you can specify straight from the table above; if not, send us the room schedule and we will match valves to it.

Previous Post Next Post

Leave A Comment